Cork flooring brings warmth, natural insulation, a soft underfoot feel, and countless other benefits to any space. Once you’ve chosen cork, you’ll need to decide on an installation method. You can choose between a floating cork floor, traditional glue-down tiles or pre-glued tiles with adhesive backing already applied.
Pre-glued cork tiles make installation even more accessible by eliminating the need to apply contact adhesive to each tile individually. The adhesive is already on the backing, with a peel-and-stick application method, so you can focus on layout and placement.
This guide covers cork tile installation step by step, whether your tiles are pre-glued or require adhesive application. If you’re not confident, we recommend leaving it to a professional entirely, or at the very least, getting a professional to handle the subfloor preparation first.
Floating, glue-down, or pre-glue, the success of any cork floor comes down to what’s underneath. Proper subfloor preparation isn’t optional. It’s the foundation that determines how well your floor performs over time. If you’re considering traditional glue-down cork tiles, the installation process is different but the subfloor requirements are equally important.
The key to success with any cork floor is achieving a good bond between the subfloor and the tile. Pre-glued cork tiles are no exception. The adhesive on the backing will only work as well as the surface it’s stuck to.
Your subfloor must be:
Even if your concrete slab is old, moisture can still be an issue. If installing over concrete without a basement underneath, you’ll need a moisture barrier. Follow the WAKOL moisture proofing system or equivalent:
Do not install cork tiles when the subfloor temperature is below 18°C or room temperature is below 18°C. Maintain relative humidity between 35-65%. Low temperatures affect how well the adhesive bonds.
Transport and store cartons flat in a dry, well-ventilated area. Let the tiles acclimatise at the installation site for a minimum of 48 hours. Keep the temperature between 18-28°C and humidity between 35-65% during this period.
Don’t remove tiles from packaging until you’re ready to install them.
Find the centre of the room using a chalk line. Measure from the middle of one wall to the middle of the opposite wall, then repeat for the other two walls. The intersection should form a 90° angle.
Dry-lay tiles (without removing the backing) to check that tiles near the walls will be at least 5cm wide. If not, adjust your centre lines.
Lay tiles following the direction of the main light source when possible.

Begin laying tiles from the centre of the room along your marked chalk lines. Use a brick-bond pattern (staggered joints) for the best appearance and stability.
Apply contact adhesive to the back of the tile and allow it to become tacky before placing. If your tiles are pre-glued, you can skip this step. Position the tile carefully along your chalk line. Once the tile makes contact with the subfloor, it adheres immediately and cannot be repositioned.
Press the tile firmly with your hands, then use a rubber hammer or hand roller to ensure full contact. Work from the center of the tile outward to eliminate air bubbles.
Repeat the process, working outward from the center. Align each tile carefully before pressing it down.
Every 30 minutes, roll the installed area with a 50kg roller to ensure tiles are firmly bedded. Roll the entire floor again when installation is complete.
Cork is a natural product and some tiles may be slightly out of square (0.5-1.0mm). Here’s how to handle this:
Cork is resilient and compresses easily. If no pressure is applied to the adhesive, the tile can still be adjusted on the subfloor.
If small gaps appear between tiles, fill them with an appropriate caulking compound or wood filler in a colour that matches the cork. For Dark cork, use Timbermate Ebony. For Light cork, use Timbermate Hardwood. Apply filler one day before sanding and finishing to allow it to dry.
Cut a strip of cork offcut at a 45° angle, slightly wider than the gap (approximately 2mm). Push the strip into the gap. The cork will compress as it enters, then decompress to fill the space.
Always cut tiles on the finished (top) side using a sharp utility knife and a straight edge.
When laying tiles against walls, cut the final tile 0.5-1.0mm longer than needed with a mitred edge. The cork will compress enough to fill the gap when pressed into place.
Cork tiles can be finished with a protective coating 24 hours after installation. Natural cork should be sealed with an appropriate polyurethane finish like Loba 2K Duo for protection and longevity.
Follow the manufacturer’s instructions for your chosen finish product. Multiple coats are typically required for proper protection.
Need additional help with your cork tile installation? Contact Market Timbers for product advice, installation support, or to order samples of our cork tiles.
We’re proud to partner with market-leading brands to bring you the best quality products.